Archives: Performance Shop
Showing 97–108 of 119 resultsSorted by price: high to low
-
Adjustable Suspension Limiting Straps
$39.99Quick ViewAdd to cartSold as a pair Adjustable from approximately 4″ to 14″ with custom lengths available Strap material is made from high strength polyester just like a seatbelt. NOT nylon, which wears faster and loses strength when wet Thick end hardware with 3/8″ holes to bolt to the frame and control arm Slide adjusters at both ends …
-
Large Bore Bolt-In Wheel Cylinders For GM Drum Brakes
$35.99Quick ViewAdd to cartSold as a pair Increases stopping power of stock drum brakes significantly and noticeably Direct replacement for any ~1.367″ bore backing plate that uses bolt-in wheel cylinder Known fitment includes but is not limited to: >1964-1967 A-Body >1968-1972 A-Body >1973-1977 A-Body >1977-1996 B-Body* >1970-1981 F-Body >1993-1997 F-Body >1968-1974 X-Body >1992-2002 S-10 Note: The oversize vs. …
Large Bore Bolt-In Wheel Cylinders For GM Drum BrakesRead More
-
Large Bore Clip-In Wheel Cylinders For GM Drum Brakes
$35.99Quick ViewAdd to cartSold as a pair Increases stopping power of stock drum brakes significantly and noticeably Direct replacement for any “Clip-type” GM wheel cylinder Known fitment includes but is not limited to: >1978-1988 A/G-Body (Metric Chassis) >1982-1992 F-Body (factory drum rear) >1982-1990 S-10 / Sonoma
-
Telescoping Adjustable Arm End – 1/2″ Rod End
$34.99Quick ViewAdd to cartWhen assembled these allow the adjustment of the center to center distance of a trailing arm or similar component without having to spin the tube itself while also not having to undo any mounting bolts. Helpful for swing arm type suspensions where the tube has a spring perch or bend that cannot be spun like …
-
1978-1988 A/G-Body Pre-Bent OEM Steel Rear Hard Lines For Disc Brake Upgrade On Factory Rear
$34.99Quick ViewAdd to cartEliminates need to shorten factory lines Pre-bent for a perfect fit Pre-flared for a truly bolt on design Note: Must be used with the stainless braided line upgrade, standard hoses in the disc brake upgrade kit are too short *Actual part not shown
-
GM Polyurethane Trailing Arm Bushings 1964-2002
$34.99Quick ViewAdd to cartSold in pairs When replacing upper trailing arms be sure to check the condition of your upper housing bushings Polyurethane offers a tighter suspension feel while still eliminating a moderate amount of road harshness New parts to replace worn and cracked factory rubber Fits >64-67 68-72 73-77 78-88 midsize A/G-Body cars, all 8 rear end …
-
1973-1977 A-Body Rear Trailing Arm Fastener Set
$22.99Quick ViewAdd to cartIncludes -8x Grade 8 1/2-13 bolts -8x Grade 8 1/2-13 nylon insert nuts -16x Grade 8 1/2 SAE flat washers All yellow zinc coated for rust prevention Torque to 75 lb/ft
-
1968-1972 A-Body Rear Trailing Arm Fastener Set
$22.99Quick ViewAdd to cartIncludes -8x Grade 8 1/2-13 bolts -8x Grade 8 1/2-13 nylon insert nuts -16x Grade 8 1/2 SAE flat washers All yellow zinc coated for rust prevention Torque to 75 lb/ft
-
1964-1967 A-Body Rear Trailing Arm Fastener Set
$22.99Quick ViewAdd to cartIncludes -8x Grade 8 1/2-13 bolts -8x Grade 8 1/2-13 nylon insert nuts -16x Grade 8 1/2 SAE flat washers All yellow zinc coated for rust prevention Torque to 75 lb/ft
-
1978-1988 A/G-Body Rear Trailing Arm Fastener Set
$22.99Quick ViewAdd to cartIncludes -8x Grade 8 1/2-13 bolts -8x Grade 8 1/2-13 nylon insert nuts -16x Grade 8 1/2 SAE flat washers All yellow zinc coated for rust prevention Torque to 75 lb/ft Note: The factory fastener size was 12mm, meaning the holes are a hair(<.020) smaller than the fasteners, a 1/2″ drill bit will make very …
-
Semi-Metallic Pads
$22.99Quick ViewAdd to cartDont upgrade your entire brake system just to leave daily driver quality pads on your ride. Get the absolute most out of your brakes. Pads fit: >MPC rear disc brake kits >1982-2002 2WD S-10 front calipers >1982-2002 F-body front calipers >1978-1988 A/G-Body front calipers Note: Sold as an axle set, meaning two sets are needed …
-
1982-2002 2WD S-10 MCP Rear Disc Brake Kit Caliper Spacer Upgrade
$19.99Quick ViewAdd to cartAllows the caliper piston to remain square in its bore by taking up the difference between the caliper designed for 1″ rotors and the aftermarket .810″ thick rotor Results in more even pad wear and therefore longer pad life A must for expensive pads, protect your investment!