Category: 1978-1988 A/G-Body
Showing 25–36 of 37 resultsSorted by price: high to low
-
Universal Proportioning Valve
$42.99Quick ViewAdd to cartUniversal proportioning valve placed in-line with the rear hard line will modulate the rear brakes Rear brakes applying harder and locking before the front is extremely dangerous and when installed and adjusted right this helps to eliminate that
-
Large Bore Clip-In Wheel Cylinders For GM Drum Brakes
$35.99Quick ViewAdd to cartSold as a pair Increases stopping power of stock drum brakes significantly and noticeably Direct replacement for any “Clip-type” GM wheel cylinder Known fitment includes but is not limited to: >1978-1988 A/G-Body (Metric Chassis) >1982-1992 F-Body (factory drum rear) >1982-1990 S-10 / Sonoma
-
1978-1988 A/G-Body Pre-Bent OEM Steel Rear Hard Lines For Disc Brake Upgrade On Factory Rear
$34.99Quick ViewAdd to cartEliminates need to shorten factory lines Pre-bent for a perfect fit Pre-flared for a truly bolt on design Note: Must be used with the stainless braided line upgrade, standard hoses in the disc brake upgrade kit are too short *Actual part not shown
-
GM Polyurethane Trailing Arm Bushings 1964-2002
$34.99Quick ViewAdd to cartSold in pairs When replacing upper trailing arms be sure to check the condition of your upper housing bushings Polyurethane offers a tighter suspension feel while still eliminating a moderate amount of road harshness New parts to replace worn and cracked factory rubber Fits >64-67 68-72 73-77 78-88 midsize A/G-Body cars, all 8 rear end …
-
1978-1988 A/G-Body Rear Trailing Arm Fastener Set
$22.99Quick ViewAdd to cartIncludes -8x Grade 8 1/2-13 bolts -8x Grade 8 1/2-13 nylon insert nuts -16x Grade 8 1/2 SAE flat washers All yellow zinc coated for rust prevention Torque to 75 lb/ft Note: The factory fastener size was 12mm, meaning the holes are a hair(<.020) smaller than the fasteners, a 1/2″ drill bit will make very …
-
Semi-Metallic Pads
$22.99Quick ViewAdd to cartDont upgrade your entire brake system just to leave daily driver quality pads on your ride. Get the absolute most out of your brakes. Pads fit: >MPC rear disc brake kits >1982-2002 2WD S-10 front calipers >1982-2002 F-body front calipers >1978-1988 A/G-Body front calipers Note: Sold as an axle set, meaning two sets are needed …
-
1978-1988 A/G-Body MCP Rear Disc Brake Kit Caliper Spacer Upgrade
$19.99Quick ViewAdd to cartAllows the caliper piston to remain square in its bore by taking up the difference between the caliper designed for 1″ rotors and the aftermarket .810″ thick rotor Results in more even pad wear and therefore longer pad life A must for expensive pads, protect your investment!
-
Steering Link Bump Steer Spacers For Increased Accuracy
$15.99Quick ViewAdd to cartIncludes one pair each of .100″, .060″, .030″ spacers Increased accuracy to further adjust and reduce your bump steer, if needed One set does one car
-
Replacement Standard Brake Pad MPC Rear Kit
$14.99Quick ViewAdd to cartStandard, affordable pad, that comes in our rear disc kit. Pads fit: >MPC rear disc brake kits >1982-2002 2WD S-10 front calipers >1982-2002 F-body front calipers >1978-1988 A/G-Body front calipers Note: Sold as an axle set, meaning two sets are needed to do the front and rear of the vehicle
-
GM Combination (Proportioning) Valve Bleed Tool
$12.99Quick ViewAdd to cartA must have tool to bleed a factory style disc/drum or disc/disc combination valves *May come in variety of colors depending on supplier stock
-
MCP Speed Bleeders
$12.99Quick ViewAdd to cart>Fit stock front calipers for 1978-1988 A/G-Bodies, 1982-1992 F-Body front calipers, 1982-2002 2WD S-10 front calipers, and MCP rear disc upgrades for A/G-Bodies >Allows bleeding with only one person >Simply crack the bleeder as normal and it will allow fluid out but not suck air back in >Tighten when finished
