GM U-Joint Steering Shaft Assembly ’79+
$109.99
Important: Verify your steering box input spline is 3/4-30 spine, if not it is most likely 13/16-30 spline which was ’77 and earlier
Eliminate the worn rubber rag joint that came stock on your classic
Firm up your steering significantly and eliminate slop, all while making more room for your header tubes
A must for a corner carver or even daily, feels like new again
Installs between the steering column and steering box
Simple install, an hours work with noticeable improvement
Fits G-Body’s, early S-10s, F-Body’s and more
These U-joints are sealed and do not require grease. The plastic factory dust shield can be retained to keep dirt and other contaminates out of the assembly. An occasional shot of our rod end spray lube will keep them friction free for years
IMPORTANT INSTALL INFO: If the u-joint does not slide over the column, chamfer the end of the column with a file until it does, you should not be hammering on this to install it. About 10% of columns need a slight amount of material removed
NOTE: Again please verify your column output is 1″ DD and steering box input is 3/4 x 30 Spline, if not we CAN modify to fit your application
NOTE: Late model S-10s have a u joint at the column from the factory, however if you wish to purchase this shaft to replace both that u-joint and the rag joint make a note in your order as we have to make this item longer
| Weight | 3 lbs |
|---|---|
| Dimensions | 2 × 3 × 17 in |
Only logged in customers who have purchased this product may leave a review.
Product Enquiry
You may also like…
-
Rod End Spray by WD-40
$9.99Quick ViewAdd to cart> Dry spray eliminates the possibility of dirt and grit sticking to the bearing surface which prematurely wears rod ends > Contains Teflon to aid in friction reduction and prolonged life > Aids in AN hose assembly > Great for seat tracks, door hinges, carburator throttle shafts etc etc
Related products
-
1978-1988 A/G-Body Rear Disc Brake Kit W/o Parking Brake
$284.99Quick ViewAdd to cartReplace old heavy drums with easy to maintain disc brakes Brand new, non-junkyard parts Kit Includes >Left and right caliper brackets >Left and right calipers >Hoses from caliper to hard line (unless purchasing new hard line the factory line must be shortened and re-flared) >Left and right rotors >Standard pads >All necessary fasteners *Shown with …
1978-1988 A/G-Body Rear Disc Brake Kit W/o Parking BrakeRead More
-
1978-1988 A/G-Body Pre-Bent Stainless Steel Rear Hard Lines For Disc Brake Upgrade On Factory Rear
$44.99Quick ViewAdd to cart>Eliminates need to shorten factory lines >Pre-bent for a perfect fit >Pre-flared for a truly bolt on design >Stainless steel to last a lifetime Note: Must be used with the stainless braided line upgrade, standard hoses in the disc brake upgrade kit are too short *Actual part not shown
-
1982-2002 A/4WD S-10 Adjustable Pro-Touring Steering Link Kit
$219.99Quick ViewAdd to cartTeflon (PTFE) lined chromoly rod ends for maximum life and minimum friction Half the weight of the factory tie rod assembly All needed fasteners included Replaces both inner and outer tie rods instead of just the outer like competitor pieces Black 6061-T6 Hard anodized adjustment tube A must to improve both cornering and straight line …
1982-2002 A/4WD S-10 Adjustable Pro-Touring Steering Link KitRead More
-
1982-2002 2WD S-10 Steering Link Kit
$219.99Quick ViewAdd to cartTeflon (PTFE) lined chromoly rod ends for maximum life and minimum friction Half the weight of the factory tie rod assembly All needed fasteners included Replaces both inner and outer tie rods instead of just the outer like competitor pieces Black 6061-T6 Hard anodized adjustment tube A must to improve both cornering and straight line …
Reviews
There are no reviews yet.