GM U-Joint Steering Shaft Assembly ’79+
$109.99
Important: Verify your steering box input spline is 3/4-30 spine, if not it is most likely 13/16-30 spline which was ’77 and earlier
Eliminate the worn rubber rag joint that came stock on your classic
Firm up your steering significantly and eliminate slop, all while making more room for your header tubes
A must for a corner carver or even daily, feels like new again
Installs between the steering column and steering box
Simple install, an hours work with noticeable improvement
Fits G-Body’s, early S-10s, F-Body’s and more
These U-joints are sealed and do not require grease. The plastic factory dust shield can be retained to keep dirt and other contaminates out of the assembly. An occasional shot of our rod end spray lube will keep them friction free for years
IMPORTANT INSTALL INFO: If the u-joint does not slide over the column, chamfer the end of the column with a file until it does, you should not be hammering on this to install it. About 10% of columns need a slight amount of material removed
NOTE: Again please verify your column output is 1″ DD and steering box input is 3/4 x 30 Spline, if not we CAN modify to fit your application
NOTE: Late model S-10s have a u joint at the column from the factory, however if you wish to purchase this shaft to replace both that u-joint and the rag joint make a note in your order as we have to make this item longer
| Weight | 3 lbs |
|---|---|
| Dimensions | 2 × 3 × 17 in |
Only logged in customers who have purchased this product may leave a review.
Product Enquiry
You may also like…
-
Rod End Spray by WD-40
$9.99Quick ViewAdd to cart> Dry spray eliminates the possibility of dirt and grit sticking to the bearing surface which prematurely wears rod ends > Contains Teflon to aid in friction reduction and prolonged life > Aids in AN hose assembly > Great for seat tracks, door hinges, carburator throttle shafts etc etc
Related products
-
1994-2002 S-10 Steering U-Joint
$64.99Quick ViewAdd to cartEliminate the rubber rag joint that came stock on your 2nd gen S-10 Firm up your S-10s steering significantly and eliminate slop A must for a corner carver Installs between the steering shaft and steering box Replaces MANY stock rag joints on different applications using Lares PN 200 Interchanges with, and is more affordable than …
-
1978-1988 A/G-Body Rear Disc Brake Kit W/o Parking Brake
$284.99Quick ViewAdd to cartReplace old heavy drums with easy to maintain disc brakes Brand new, non-junkyard parts Kit Includes >Left and right caliper brackets >Left and right calipers >Hoses from caliper to hard line (unless purchasing new hard line the factory line must be shortened and re-flared) >Left and right rotors >Standard pads >All necessary fasteners *Shown with …
1978-1988 A/G-Body Rear Disc Brake Kit W/o Parking BrakeRead More
-
1978-1988 A/G-Body MCP Rear Disc Brake Kit Caliper Spacer Upgrade
$19.99Quick ViewAdd to cartAllows the caliper piston to remain square in its bore by taking up the difference between the caliper designed for 1″ rotors and the aftermarket .810″ thick rotor Results in more even pad wear and therefore longer pad life A must for expensive pads, protect your investment!
-
1978-1988 A/G-Body DOT Approved Stainless Steel Braided Brake Hose Kit
$84.99Quick ViewAdd to cartIncludes frame to rear end hose that most kits do not A must for any vehicle with rubber hoses as they swell, reducing stopping power and making the car pull to one side under braking Will significantly increase brake pedal feel The absolute best bang for your buck, inexpensive brake upgrade around
Reviews
There are no reviews yet.