GM U-Joint Steering Shaft Assembly ’79+
$109.99
Important: Verify your steering box input spline is 3/4-30 spine, if not it is most likely 13/16-30 spline which was ’77 and earlier
Eliminate the worn rubber rag joint that came stock on your classic
Firm up your steering significantly and eliminate slop, all while making more room for your header tubes
A must for a corner carver or even daily, feels like new again
Installs between the steering column and steering box
Simple install, an hours work with noticeable improvement
Fits G-Body’s, early S-10s, F-Body’s and more
These U-joints are sealed and do not require grease. The plastic factory dust shield can be retained to keep dirt and other contaminates out of the assembly. An occasional shot of our rod end spray lube will keep them friction free for years
IMPORTANT INSTALL INFO: If the u-joint does not slide over the column, chamfer the end of the column with a file until it does, you should not be hammering on this to install it. About 10% of columns need a slight amount of material removed
NOTE: Again please verify your column output is 1″ DD and steering box input is 3/4 x 30 Spline, if not we CAN modify to fit your application
NOTE: Late model S-10s have a u joint at the column from the factory, however if you wish to purchase this shaft to replace both that u-joint and the rag joint make a note in your order as we have to make this item longer
| Weight | 3 lbs |
|---|---|
| Dimensions | 2 × 3 × 17 in |
Only logged in customers who have purchased this product may leave a review.
Product Enquiry
You may also like…
-
Rod End Spray by WD-40
$9.99Quick ViewAdd to cart> Dry spray eliminates the possibility of dirt and grit sticking to the bearing surface which prematurely wears rod ends > Contains Teflon to aid in friction reduction and prolonged life > Aids in AN hose assembly > Great for seat tracks, door hinges, carburator throttle shafts etc etc
Related products
-
GM Splined Column U-Joint Steering Shaft Assembly (’78 A/G-Body)
$109.99Quick ViewAdd to cartNote: These are specifically for GM application with splined column shafts, which were rare. 78 A/G-Body being the best example. Eliminate the rubber rag joint that came stock on your classic Firm up your steering significantly and eliminate slop, all while making more room for your header tubes A must for a corner carver or …
GM Splined Column U-Joint Steering Shaft Assembly (’78 A/G-Body)Read More
-
1978-1988 A/G-Body Performance Disc Brake Kit W/ Parking Brake
$549.99Quick ViewAdd to cartOutpacing (or out-stopping) this kit requires thousands of dollars Includes our rear disc kit w/ parking brake Braided hoses for the front and frame to rear end to tighten brake feel Large bore front calipers deliver more clamping force to the rotor Brand new, non-junkyard parts Note: The MCP rear disc brake conversion included in …
1978-1988 A/G-Body Performance Disc Brake Kit W/ Parking BrakeRead More
-
MCP Speed Bleeders
$12.99Quick ViewAdd to cart>Fit stock front calipers for 1978-1988 A/G-Bodies, 1982-1992 F-Body front calipers, 1982-2002 2WD S-10 front calipers, and MCP rear disc upgrades for A/G-Bodies >Allows bleeding with only one person >Simply crack the bleeder as normal and it will allow fluid out but not suck air back in >Tighten when finished
-
GM Rubber Trailing Arm Bushings 1964-2002
$9.99Quick ViewAdd to cartSold in pairs When replacing upper trailing arms be sure to check the condition of your upper housing bushings Rubber allows a good bit of articulation while still absorbing a large amount of harshness from the road New parts at OEM quality to replace worn and cracked factory rubber Fits 64-67 68-72 73-77 78-88 midsize …
Reviews
There are no reviews yet.